The intelligent brick can be programmed using official software available for Windows and Mac computers, and is downloaded onto the brick via Bluetooth or a USB cable. There are also several unofficial programs and compatible programming languages that have been made to work with the brick, and many books have been written to support this community.
Stickers are used for decorations for the outside of the plane. I like how the stickers for the outside match colours with the piping on the plane. I found the sticker for the top of the door to be a little big; if you line up the orange on the bottom of the stickers with the orange on the plane the sticker overlaps a bit at the top. The stickers for the nose of the plane are not as difficult to apply as I thought they would be. They do seem a bit superfluous, though they do make the plane look nice. The plane is finished with the tail fin, that uses yet more stickers. It is interesting that this plane actually uses more stickers than the Friends plane does.
Here’s a look at the Winter Soldier and Captain America minifigures. Unfortunately, neither one of them is exclusive to this set, with this version of Winter Soldier making an appearance in 76047 Black Panther Pursuit. Captain America has been a lot more promiscuous, having made an appearance in 2 sets (Quinjet City Chase & Hydra Fortress Smash) and a polybag as well. His torso is also identical to the one from Black Panther Pursuit.
The upper and lower wings are connected by a dark bluish grey 4 x 1 x 3 tail on either side; this tail element is unique to the set in this colour, although has previously appeared in a couple of sets back in 2003 in old dark grey. The upper wing is also supported by a couple of 1 x 2 x 2 black windows placed back to back in front of the cockpit, which from the perspective of the pilot really can’t be good for visibility. The biplane has a three blade propeller and the tips of the blades are stickered prior to sliding the propeller on to a 6L axle protruding from the front of the fuselage where it’s held in place by an orange 2 x 2 brick with domed top. The last step is to attach a 1 x 4 x 2 bar to the top of the upper wing for the Wing Walker to hold on to and then we’re done with the biplane.
Pack your bags and get ready to go on vacation! Head to the airport and check in at the terminal. Put your luggage on the conveyor belt and watch it get loaded onto the passenger airplane. Go through security and then head out the revolving doors to the loading area. Climb the stairs and get buckled in, your trip is about to start! This creative play building toy includes 6 minifigures.
I did prefer the previous 3182 airport set as it had a lot more components. But, I realise that it makes more business sense to offer a little less than raise the price of an already expensive product. However, 60104 is still a nice set and is often very well discounted in the UK so, I ordered a pallet load from Tesco during their 3-for-2 which made them a half-priced no-brainer ;-)
If you don’t own Black Panther Pursuit or any of the sets that included Captain America, I guess it would a plus getting the both of them in this set but Super Heroes collectors tend to be completionists, so I think that scenario will be particularly rare. I guess you could always sell your spares on the secondary market, but really, who wants to do that?
A minifigure can comfortably fit seated inside the cockpit, and it is here that I found the first issue with the set. I had no issue inserting and removing the figure from his seated position, but my seven-year old struggled to get him out, deciding to leave him onboard instead of disembarking after she brought the jet back into the hangar. The physical connection between LEGO pieces in the cockpit and the pilot minifigure didn’t seem to present an issue, so whether or not this was just a one-off issue remains to be seen.
Primary concept and development work takes place at the Billund headquarters, where the company employs approximately 120 designers. The company also has smaller design offices in the UK, Spain, Germany, and Japan which are tasked with developing products aimed specifically at these markets. The average development period for a new product is around twelve months, split into three stages. The first stage is to identify market trends and developments, including contact by the designers directly with the market; some are stationed in toy shops close to holidays, while others interview children. The second stage is the design and development of the product based upon the results of the first stage. As of September 2008 the design teams use 3D modelling software to generate CAD drawings from initial design sketches. The designs are then prototyped using an in-house stereolithography machine. These prototypes are presented to the entire project team for comment and for testing by parents and children during the "validation" process. Designs may then be altered in accordance with the results from the focus groups. Virtual models of completed Lego products are built concurrently with the writing of the user instructions. Completed CAD models are also used in the wider organisation, for marketing and packaging.
I'm not sure what to make of the set yet. I like the planes (although that biplane really doesn't need the bubble canopy). The idea of adding a hangar is interesting and I don't mind that it's a bit open. But the fact that it'll only house one of the three planes is annoying. Having said that, I'm not sure what you could do about it. Tripling the hangar would make it big and boring and push the price up. Could they have done two planes and a double hangar?