I like the nod to the classic LEGO Ideas Book with the 'Follow Me' sticker, but overall I think the F-18 type jet is redundant, making the whole thing over-priced. Had it been presented in a different colour scheme from the Viggen, and maybe a bit of a sleeker or more agile design in itself, it might have been a worthwhile inclusion. But as it is, it just superficially looks like two fairly similar aircraft, and thus quite a bit less value for money as a set.
The upper and lower wings are connected by a dark bluish grey 4 x 1 x 3 tail on either side; this tail element is unique to the set in this colour, although has previously appeared in a couple of sets back in 2003 in old dark grey. The upper wing is also supported by a couple of 1 x 2 x 2 black windows placed back to back in front of the cockpit, which from the perspective of the pilot really can’t be good for visibility. The biplane has a three blade propeller and the tips of the blades are stickered prior to sliding the propeller on to a 6L axle protruding from the front of the fuselage where it’s held in place by an orange 2 x 2 brick with domed top. The last step is to attach a 1 x 4 x 2 bar to the top of the upper wing for the Wing Walker to hold on to and then we’re done with the biplane.
If you don’t own Black Panther Pursuit or any of the sets that included Captain America, I guess it would a plus getting the both of them in this set but Super Heroes collectors tend to be completionists, so I think that scenario will be particularly rare. I guess you could always sell your spares on the secondary market, but really, who wants to do that?
Honestly I have asked many of my friends and only a number even know about LEGO’s removal tool piece, and this is already an updated one from their previous grey piece. Friends, family, strangers – this is a lifesaver. It wouldn’t save you from stepping on a LEGO piece but it helps a tonne in getting pieces off of each other without damaging your nails. Or teeth. Don’t ask.
Every good airport needs a hangar for the planes, and this is no exception. The satisfactory hangar included here does come across as rather basic, and while it doesn’t detract from the overall package, it isn’t going to swing your decision over whether to purchase this (and truthfully, I think you would have already made that decision before you come to the hangar). The design itself is simple, with the build unlikely to take you more than 10 minutes. That being said, it is a well-built piece and doesn’t feel flimsy, which was the impression I had when I first saw a picture of it. The criss-cross pieces towards the base give it a firm foundation, and there are plenty of long pieces which add further stability to it. Plane-wise, it is best suited for the old-fashioned vehicle, with the orange colouring in the design going well with the plane. Only a couple of stickers in use here, with just the AIRSHOW HANGAR words needing to be added.
The last of the three aircraft is a modern biplane. This incorporates a number of rare orange elements including right and left 8 x 3 wedge plates which make up the wings and have only previously appeared in three sets, a 3 x 4 wedge brick only previously found in two sets, and a 3 x 6 round half plate with a 1 x 2 cutout which has only previous appeared in a single set in this colour and which forms the tailplanes. Similar to the two jets the tail fin is stickered rather than printed, as are the pair of 1 x 4 x 1 panels making up the sides of the cockpit. Unlike the jets, however, the instrument panel is stickered, which seems odd as there are existing printed 1 x 2 light bluish grey tiles which could have done an acceptable job. There are also a pair of stickers which represent the engine exhausts and which are applied to a couple of modified 2 x 4 x 1 1/3 bricks with curved top which sit just behind the propeller; applying these neatly to the curved surface takes a steady hand, and that’s also the case for the pair of checkerboard stickers which are stuck onto the propeller cowl. As if stickered exhausts weren’t enough, there are also a couple of light bluish grey exhaust pipes with Technic pin which emerge from the propeller cowl and run along either side of the fuselage. They’re entirely superfluous given the presence of the stickered exhausts but they still look cool regardless!
The remainder of the build is the control tower and terminal building. First there is a metal detector screener leading to the waiting/secure area of the airport, which seems taller than it needs to be for the minifigures. I think the same effect could have been made with half the height, except that would not allow for an impressive height for the overall tower. However it does seem to be similar to many modern airports with the high ceilings. This area also seems to be someplace to check luggage as evidenced by the rather nifty conveyor belt that comes in a full part. The moving parts of the set include a revolving door (a very tall one, for the first floor) that leads from the secure area of the airport out to the tarmac, and of course the conveyor belt.
The main constituents of the set are a tanker truck, three aircraft and a hangar. Each of these gets its own instruction booklet and bags of elements. First up is the tanker truck (below) which at only four studs wide and less than ten studs in length reminds me of the 4-stud wide vehicles of my youth. This impression is reinforced by the inclusion of a couple of late 70’s-style 2 x 4 mudguards in the build.
A minifigure can comfortably fit seated inside the cockpit, and it is here that I found the first issue with the set. I had no issue inserting and removing the figure from his seated position, but my seven-year old struggled to get him out, deciding to leave him onboard instead of disembarking after she brought the jet back into the hangar. The physical connection between LEGO pieces in the cockpit and the pilot minifigure didn’t seem to present an issue, so whether or not this was just a one-off issue remains to be seen.
The two stunt jets included here actually have some similarity in the basic design and colour scheme to the main piece seen in the Marvel Super Heroes Avenjet Space Mission set. With that being said, I loved the Avenjet in that particular set, so any similarity holds no issue with me. The red and white colours work really well together, and it looks like something you would genuinely see flying through the sky at an air show. I really love it when LEGO truly capture the essence of what you are building, and they do that here. The jets themselves, as I said before, are similar to previously-released jets, and therefore the builds won’t come as any main surprise. That shouldn’t detract from the product, however, as it is a prime example of LEGO finding a winning formula and not really needing to change it.
My personal favourite of the three planes included in this set, the design is superb and really captures the look and feel of the old-fashioned airplane that it is based on. The build isn’t too complex, and it really is a joy to see the final product come together. The plane has a distinct orange colour scheme, with some black and grey thrown in, and the shades work well together.
Anyway, I think this may be my favorite LEGO City air terminal yet! It may not be as big as some previous ones, but it feels really coherent. The plane is nice as well with its white, orange, and blue stripes. I agree that Heartlake City Airport's plane has a cozier and more detailed interior, though. It does really highlight some of the differences between Friends and City, with City opting for capacity over comfort and function over flair.
Parking capacity at Copenhagen Airport was greatly expanded in 2015 with the construction of a new lot as one of the first phases in an ambitious airport expansion plan scheduled to roll out in the coming decades. There are several lots: those near the terminals are very expensive, while the further-flung ones are cheaper (but have free shuttle bus service to the terminals).