Colour-wise, it is mainly yellow, with only a dash of green and red, and a little more white, there to break it up. The worker has space to stand and drive the vehicle, and has a walkie talkie attached on the side of the car. Around the other side is a coiled-up, what I assume is a, fuel pump. It looks pretty good when coiled up on the side of the car. Stickers come into use again here, this time for the number plates.
The box set weighs a little over 2kg and has about 694 pieces in total, including 6 minifigures: a pilot, 3 airport workers, a male and a female passenger. The whole build would get you almost an entire airport facade with a pretty big passenger plane, an airport/control tower build, and an airport service car that tows with it a luggage, fuel and and mobile stairway.
Since 1963, Lego pieces have been manufactured from a strong, resilient plastic known as acrylonitrile butadiene styrene (ABS). As of September 2008, Lego engineers use the NX CAD/CAM/CAE PLM software suite to model the elements. The software allows the parts to be optimised by way of mould flow and stress analysis. Prototype moulds are sometimes built before the design is committed to mass production. The ABS plastic is heated to 232 °C (450 °F) until it reaches a dough-like consistency. It is then injected into the moulds at pressures between 25 and 150 tonnes, and takes approximately 15 seconds to cool. The moulds are permitted a tolerance of up to twenty micrometres, to ensure the bricks remain connected. Human inspectors check the output of the moulds, to eliminate significant variations in colour or thickness. According to the Lego Group, about eighteen bricks out of every million fail to meet the standard required. Lego factories recycle all but about 1 percent of their plastic waste from the manufacturing process. If the plastic cannot be re-used in Lego bricks, it is processed and sold on to industries that can make use of it. Lego has a self-imposed 2030 deadline to find a more eco-friendly alternative to the ABS plastic it currently uses in its bricks.
I like the nod to the classic LEGO Ideas Book with the 'Follow Me' sticker, but overall I think the F-18 type jet is redundant, making the whole thing over-priced. Had it been presented in a different colour scheme from the Viggen, and maybe a bit of a sleeker or more agile design in itself, it might have been a worthwhile inclusion. But as it is, it just superficially looks like two fairly similar aircraft, and thus quite a bit less value for money as a set.
By 1954, Christiansen's son, Godtfred, had become the junior managing director of the Lego Group. It was his conversation with an overseas buyer that led to the idea of a toy system. Godtfred saw the immense potential in Lego bricks to become a system for creative play, but the bricks still had some problems from a technical standpoint: their locking ability was limited and they were not versatile. In 1958, the modern brick design was developed; it took five years to find the right material for it, ABS (acrylonitrile butadiene styrene) polymer. The modern Lego brick design was patented on 28 January 1958.
The last of the three aircraft is a modern biplane. This incorporates a number of rare orange elements including right and left 8 x 3 wedge plates which make up the wings and have only previously appeared in three sets, a 3 x 4 wedge brick only previously found in two sets, and a 3 x 6 round half plate with a 1 x 2 cutout which has only previous appeared in a single set in this colour and which forms the tailplanes. Similar to the two jets the tail fin is stickered rather than printed, as are the pair of 1 x 4 x 1 panels making up the sides of the cockpit. Unlike the jets, however, the instrument panel is stickered, which seems odd as there are existing printed 1 x 2 light bluish grey tiles which could have done an acceptable job. There are also a pair of stickers which represent the engine exhausts and which are applied to a couple of modified 2 x 4 x 1 1/3 bricks with curved top which sit just behind the propeller; applying these neatly to the curved surface takes a steady hand, and that’s also the case for the pair of checkerboard stickers which are stuck onto the propeller cowl. As if stickered exhausts weren’t enough, there are also a couple of light bluish grey exhaust pipes with Technic pin which emerge from the propeller cowl and run along either side of the fuselage. They’re entirely superfluous given the presence of the stickered exhausts but they still look cool regardless!
This set has essentially all that's needed for airplane-related play: the plane, an airport terminal, and a service vehicle. And each part of the set is quite detailed. The plane feature a galley and a toilet; the service vehicle has stairs, a baggage trailer, etc; and the terminal has revolving doors, security check, and a baggage conveyor belt. The building process is also well planned out and documented. The child is eased into building by starting out with the service vehicle, then comes the plane, and last the terminal, which can be challenging.
The set contains six minifigures. Even though they all incorporate standard, unprinted minifigure legs together with commonly-available headprints, it appears that all six are unique to the set. First up are two members of the Ground Crew (below). The bearded guy has an orange torso printed with a hi-viz jacket, ID badge and red pen pattern. This has appeared in nine sets to date including all of the 2016 Airport sets plus 60080 Spaceport which I reviewed here last summer. His red construction helmet, which incorporates a pair of non-removable black ear muffs, has appeared in less than ten sets to date. The other member of the ground crew has a rather nice printed medium blue torso which is new this year and has only appeared in a total of three sets including this one. It features a shirt print which includes the Octan logo and a top pocket complete with a pen.
It’s always tough to sum up a set that has the sort of price tag that this one carries; because it doesn’t necessarily offer the collectors value that a Marvel or Star Wars set will offer, it can be a little harder to justify an outlay on, in this case, a few planes and a aircraft hangar. However, if you have a love for the City range, whether it be a nostalgic look back at your childhood, the general consistently-superior design of the range, or simply because your kids want an airport to build, this one has to be recommended. Once I finished building this, I set it up in my daughter’s bedroom, and the overjoyed expression on her face, followed by the extended time taken to play with the planes and flying them all over her room, made every single minute of the build worthwhile. Watching her swirl around her room – and later, the rest of house – clutching the planes and bringing them in for landings into the hangar, reminded me of why I fell in love with LEGO in the the first place; imagination.