The cockpit, including the stickers on the sides and the canopy, is identical to that of the first jet, as is the front of the aircraft. As previously noted, however, the wing configuration is different, as is the tail design which features twin tail fins and a pair of fuselage-mounted tailplanes. The red 4 x 1 x 3 tail fins, which have appeared in a total of seven sets including this one, are angled outwards similar to the arrangement on an F/A-18 Hornet. Overall, it’s another sleek design but once again the smooth lines are somewhat spoiled by the prominent canopy.
The remainder of the build is the control tower and terminal building. First there is a metal detector screener leading to the waiting/secure area of the airport, which seems taller than it needs to be for the minifigures. I think the same effect could have been made with half the height, except that would not allow for an impressive height for the overall tower. However it does seem to be similar to many modern airports with the high ceilings. This area also seems to be someplace to check luggage as evidenced by the rather nifty conveyor belt that comes in a full part. The moving parts of the set include a revolving door (a very tall one, for the first floor) that leads from the secure area of the airport out to the tarmac, and of course the conveyor belt.
The last of the three aircraft is a modern biplane. This incorporates a number of rare orange elements including right and left 8 x 3 wedge plates which make up the wings and have only previously appeared in three sets, a 3 x 4 wedge brick only previously found in two sets, and a 3 x 6 round half plate with a 1 x 2 cutout which has only previous appeared in a single set in this colour and which forms the tailplanes. Similar to the two jets the tail fin is stickered rather than printed, as are the pair of 1 x 4 x 1 panels making up the sides of the cockpit. Unlike the jets, however, the instrument panel is stickered, which seems odd as there are existing printed 1 x 2 light bluish grey tiles which could have done an acceptable job. There are also a pair of stickers which represent the engine exhausts and which are applied to a couple of modified 2 x 4 x 1 1/3 bricks with curved top which sit just behind the propeller; applying these neatly to the curved surface takes a steady hand, and that’s also the case for the pair of checkerboard stickers which are stuck onto the propeller cowl. As if stickered exhausts weren’t enough, there are also a couple of light bluish grey exhaust pipes with Technic pin which emerge from the propeller cowl and run along either side of the fuselage. They’re entirely superfluous given the presence of the stickered exhausts but they still look cool regardless!
A minifigure can comfortably fit seated inside the cockpit, and it is here that I found the first issue with the set. I had no issue inserting and removing the figure from his seated position, but my seven-year old struggled to get him out, deciding to leave him onboard instead of disembarking after she brought the jet back into the hangar. The physical connection between LEGO pieces in the cockpit and the pilot minifigure didn’t seem to present an issue, so whether or not this was just a one-off issue remains to be seen.
Last to be assembled is the hangar, which given its size is a surprisingly quick build – even though I’m a notoriously slow builder it took me barely ten minutes to put it together. The first step involves stacking dark bluish grey and orange plates and tiles to create a three-sided enclosure covering an area of 24 x 32 studs. Two side walls are then constructed from 1 x 6 x 5 rectangular girders topped off with dark bluish grey bricks and orange tiles, after which the roof is assembled, predominantly from a few large plates including a black 8 x 16 plate only previously available in two sets, and four dark bluish grey 6 x 24 plates which are only appearing in a set for the second time ever. A couple of stickers at the front of the structure identify it as an Airshow Hanger; to be frank, describing it as a hanger is probably exaggerating the case a bit as with its open front and rear it’s more akin to a large shelter.
My Lego Network is a social networking site that involves items, blueprints, ranks, badges which are earned for completing certain tasks, trading and trophies called masterpieces which allow users to progress to go to the next rank. The website has a built in inbox which allows users to send pre written messages to one another. The Lego Network includes automated non-player characters within called "Networkers", who are able to do things which normal users cannot do, sending custom messages, and selling masterpieces and blueprints. The site also has modules which are set up on the user's page that give the user items, or that display picture compositions. Before My Lego Network, there were Lego Club Pages, which essentially held the same purpose, although the design lacked complex interaction.
Colour-wise, it is mainly yellow, with only a dash of green and red, and a little more white, there to break it up. The worker has space to stand and drive the vehicle, and has a walkie talkie attached on the side of the car. Around the other side is a coiled-up, what I assume is a, fuel pump. It looks pretty good when coiled up on the side of the car. Stickers come into use again here, this time for the number plates.