Apart from that, both carriers have extensive networks within Europe and the Mediterranean (including North Africa and the Middle East). SAS flies to most European capitals, and has a particularly dense network of connections across the Baltic Sea, to Finland, Estonia, Latvia and Lithuania, as well as to Poland, where it serves the majority of even small airports. There is also a fairly good network of connections to the United Kingdom and, perhaps surprisingly, to Italy, where even smaller airports like Bologna are served.
Since 1963, Lego pieces have been manufactured from a strong, resilient plastic known as acrylonitrile butadiene styrene (ABS).[12][30] As of September 2008, Lego engineers use the NX CAD/CAM/CAE PLM software suite to model the elements. The software allows the parts to be optimised by way of mould flow and stress analysis. Prototype moulds are sometimes built before the design is committed to mass production. The ABS plastic is heated to 232 °C (450 °F) until it reaches a dough-like consistency. It is then injected into the moulds at pressures between 25 and 150 tonnes, and takes approximately 15 seconds to cool. The moulds are permitted a tolerance of up to twenty micrometres, to ensure the bricks remain connected.[33] Human inspectors check the output of the moulds, to eliminate significant variations in colour or thickness. According to the Lego Group, about eighteen bricks out of every million fail to meet the standard required.[37] Lego factories recycle all but about 1 percent of their plastic waste from the manufacturing process. If the plastic cannot be re-used in Lego bricks, it is processed and sold on to industries that can make use of it.[38][39] Lego has a self-imposed 2030 deadline to find a more eco-friendly alternative to the ABS plastic it currently uses in its bricks.[40]
The cockpit, including the stickers on the sides and the canopy, is identical to that of the first jet, as is the front of the aircraft. As previously noted, however, the wing configuration is different, as is the tail design which features twin tail fins and a pair of fuselage-mounted tailplanes. The red 4 x 1 x 3 tail fins, which have appeared in a total of seven sets including this one, are angled outwards similar to the arrangement on an F/A-18 Hornet. Overall, it’s another sleek design but once again the smooth lines are somewhat spoiled by the prominent canopy.
The differences between the two jets mainly come on the top and rear of the builds. One has a larger single rear fin and two larger wings at the back, while the other has two smaller fins and the large wings positioned in the middle of the vehicle. The nose and cockpit areas are identical on both jets, and both come with stickers; the airshow logo on the wings, and a plane motif on the sides.
LEGO CITY has some recurring themes that can get old after a while and obviously are meant for younger LEGO fans.  The Fire and Police themes within CITY quickly come to mind as it seems like they have a new run each year.  The Airport theme is one of those that doesn't quite occur every year.  The last airport set was released in 2010 and was set #3182.  This year (2016) another airport was released.  #60104, Airport Passenger Terminal, was released on 1 August 2016 in the US.  It costs $99.99 in the US and contains 694 pieces or $0.144 per piece.  I picked the set up from Amazon at 20% off or $80 ($0.115 per piece).  Yay sales!  Onto the review...
The road distance is to Billund 3 kilometres (2 mi), to Vejle 28 kilometres (17 mi), to Kolding 41 kilometres (25 mi), to Esbjerg 61 kilometres (38 mi) and to Aarhus 98 kilometres (61 mi). There are airport buses to Horsens, Skanderborg and Aarhus. Eight additional bus services operate from the airport. There are six parking zones named after countries of the world, USA, Australia, Kenya, Spain, Egypt and Greenland. Three of the zones are connected by a shuttle bus, the other three being within walking distance.
The remainder of the build is the control tower and terminal building. First there is a metal detector screener leading to the waiting/secure area of the airport, which seems taller than it needs to be for the minifigures. I think the same effect could have been made with half the height, except that would not allow for an impressive height for the overall tower. However it does seem to be similar to many modern airports with the high ceilings. This area also seems to be someplace to check luggage as evidenced by the rather nifty conveyor belt that comes in a full part. The moving parts of the set include a revolving door (a very tall one, for the first floor) that leads from the secure area of the airport out to the tarmac, and of course the conveyor belt.
This set is designed for children aged 6+, and one of the ways that it is suitable for them is the inclusion of separate instruction booklets and numbered bags for the different parts of the set (see my post about LEGO age range suitability here).  A younger modeller can build the plane or other item of their choice as soon as they open the box. It's not so much one big set as 5 different parts which make a whole scene. My 7 year old son chose to build a jet first of all...

LIC - LEGO Instruction Creator, developed by Jeremy Czajkowski, is a cross-platform, Python, OpenGL & Qt powered desktop application for creating and editing LEGO instruction books. LIC imports 3D models, organizes them into submodels, pages & steps, and exports the end result as images or PDF. A rich, WYSIWYG UI editor, which provides a fully interactive preview window along side a drag & drop-enabled navigation tree, to help organize and layout your book. Portions of LIC are based on work of Remi Gagne. LIC will be part of the AIOI - LDraw All-In-One-Installer.
The first few bags build the small truck with carts that you see on airport runways. The truck has a "follow me" sign that I confess I have not seen at any airport. There is also a fueling tank and a rolling staircase that sits next to the plane to allow for boarding. Both the tank and the staircase are additional carts for the truck, though I am guessing not both at the same time.
Will agree with some other reviewers that some parts will fall off with normal-rough play. However, the attention to detail is pretty cool and almost makes up for it. The top is hard to take off and put on to move the minifigs. There is a TSA checkpoint, a conveyor belt for luggage, a rather impressive runway vehicle. Couple this with the cargo plane or another airplane set and some atraight road nameplates, you got an airport without spending a fortune.
The upper and lower wings are connected by a dark bluish grey 4 x 1 x 3 tail on either side; this tail element is unique to the set in this colour, although has previously appeared in a couple of sets back in 2003 in old dark grey. The upper wing is also supported by a couple of 1 x 2 x 2 black windows placed back to back in front of the cockpit, which from the perspective of the pilot really can’t be good for visibility. The biplane has a three blade propeller and the tips of the blades are stickered prior to sliding the propeller on to a 6L axle protruding from the front of the fuselage where it’s held in place by an orange 2 x 2 brick with domed top. The last step is to attach a 1 x 4 x 2 bar to the top of the upper wing for the Wing Walker to hold on to and then we’re done with the biplane.
This set is designed for children aged 6+, and one of the ways that it is suitable for them is the inclusion of separate instruction booklets and numbered bags for the different parts of the set (see my post about LEGO age range suitability here).  A younger modeller can build the plane or other item of their choice as soon as they open the box. It's not so much one big set as 5 different parts which make a whole scene. My 7 year old son chose to build a jet first of all...
If you don’t own Black Panther Pursuit or any of the sets that included Captain America, I guess it would a plus getting the both of them in this set but Super Heroes collectors tend to be completionists, so I think that scenario will be particularly rare. I guess you could always sell your spares on the secondary market, but really, who wants to do that?
The set contains six minifigures. Even though they all incorporate standard, unprinted minifigure legs together with commonly-available headprints, it appears that all six are unique to the set. First up are two members of the Ground Crew (below). The bearded guy has an orange torso printed with a hi-viz jacket, ID badge and red pen pattern. This has appeared in nine sets to date including all of the 2016 Airport sets plus 60080 Spaceport which I reviewed here last summer. His red construction helmet, which incorporates a pair of non-removable black ear muffs, has appeared in less than ten sets to date. The other member of the ground crew has a rather nice printed medium blue torso which is new this year and has only appeared in a total of three sets including this one. It features a shirt print which includes the Octan logo and a top pocket complete with a pen.
The main constituents of the set are a tanker truck, three aircraft and a hangar. Each of these gets its own instruction booklet and bags of elements. First up is the tanker truck (below) which at only four studs wide and less than ten studs in length reminds me of the 4-stud wide vehicles of my youth. This impression is reinforced by the inclusion of a couple of late 70’s-style 2 x 4 mudguards in the build.
I agree to Target collecting my personal information to improve Target's retail offering, conduct product and market research, and analyse my purchasing and online activity. This includes receiving marketing communications and targeted advertising subject to me exercising my privacy rights and choices. Target may provide my personal information to service providers (some of whom may be located outside Australia) to assist with services like data processing, data analysis, printing, contact centre services, business consulting, auditing, archival, delivery and mailing services.
The design on the jet pilots’ outfits are very good, with a darker blue colour scheme offset with a red/white/yellow stripe pattern on the torso. The requisite wings and plane emblem complete the look, with the star-emblazoned helmet the icing on the cake. However, as good as those outfits are, I think the bi-plane pilots’ attire is even better, with a swish darker red colour on the legs and above the waist, culminating in a flame-effect design merging into a white torso. The old-fashioned flying helmets and goggles look great and really compliment the overall figure design.
The intelligent brick can be programmed using official software available for Windows and Mac computers, and is downloaded onto the brick via Bluetooth or a USB cable. There are also several unofficial programs and compatible programming languages that have been made to work with the brick, and many books have been written to support this community.[52]

Agent 13 has a pretty plain appearance, with caramel-coloured wavy hair, and a black, spy-like top. Her torso has some nice details, with sharp, angular lines that all combine to form a rough outline of an upside down star. She has plain sand blue pants and rocks a sub-machine gun accessory. I like regular LEGO firearms, so it’s very nice to get one in this set as they’re fairly uncommon.