Last to be assembled is the hangar, which given its size is a surprisingly quick build – even though I’m a notoriously slow builder it took me barely ten minutes to put it together. The first step involves stacking dark bluish grey and orange plates and tiles to create a three-sided enclosure covering an area of 24 x 32 studs. Two side walls are then constructed from 1 x 6 x 5 rectangular girders topped off with dark bluish grey bricks and orange tiles, after which the roof is assembled, predominantly from a few large plates including a black 8 x 16 plate only previously available in two sets, and four dark bluish grey 6 x 24 plates which are only appearing in a set for the second time ever. A couple of stickers at the front of the structure identify it as an Airshow Hanger; to be frank, describing it as a hanger is probably exaggerating the case a bit as with its open front and rear it’s more akin to a large shelter.
I'm not sure what to make of the set yet. I like the planes (although that biplane really doesn't need the bubble canopy). The idea of adding a hangar is interesting and I don't mind that it's a bit open. But the fact that it'll only house one of the three planes is annoying. Having said that, I'm not sure what you could do about it. Tripling the hangar would make it big and boring and push the price up. Could they have done two planes and a double hangar?
The remainder of the build is the control tower and terminal building. First there is a metal detector screener leading to the waiting/secure area of the airport, which seems taller than it needs to be for the minifigures. I think the same effect could have been made with half the height, except that would not allow for an impressive height for the overall tower. However it does seem to be similar to many modern airports with the high ceilings. This area also seems to be someplace to check luggage as evidenced by the rather nifty conveyor belt that comes in a full part. The moving parts of the set include a revolving door (a very tall one, for the first floor) that leads from the secure area of the airport out to the tarmac, and of course the conveyor belt.
City has had many games since it was released. One in particular, The Robot Chronicles, was a cross-over game which saw the City, Racers, and Agents 2.0 all together in Lego City, where the player controlled and unlocked vehicles in each theme to play through a campaign. This campaign/game was also tied into a My LEGO Network The Robot Chronicles campaign- playing the game earned rewards in MLN which could be used in that campaign to eventually get the Key to LEGO City.
The main wings are made up of a pair of white 10 x 10 wedge plates with cut corner and no studs in the centre; these are rare, having only previously appeared in two sets in this colour. The red 1 x 1 plate with tooth on each wing tip is also uncommon, having appeared in less than ten sets to date. The sides of the cockpit are made up of stickered red 1 x 4 x 1 panels, and it definitely helps if you concentrate when you apply the stickers, which I clearly didn’t as you can see in the picture below…. The area behind the cockpit canopy is nicely contoured by a red 4 x 4 triple wedge which, I was surprised to discover, has only previously appeared in a single set in this colour. Not to be outdone, however, the large 12 x 2 x 5 tail is appearing for the very first time in red. The hinged trans-black cockpit canopy is yet another rare element, appearing here for only the second time ever; rare it might be, but its pronounced curvature unfortunately means that it somewhat spoils the hitherto sleek lines of the jet. The flipside of this, however, is that the cockpit can comfortably accommodate the pilot.
Airport Passenger Terminal with control tower and conveyor belt measures over 11” high, 12” wide and 4” deep. Airplane measures over 7” high, 18” long and 19” wide. Service car measures over 1” high, 2” long and 1” wide. Luggage trailer measures over 3" long, 1" high and 1" wide. Fuel trailer measures over 1” high, 3” long and 1” wide. Mobile stairway measures over 2” high, 2” long and 1” wide

Correct - the hanger can only accommodate the biplane. That having been said, in order to accommodate the other aircraft too the hangar would have to be huge, with an enormous footprint, and a substantially increased parts count. As a result, I'd estimate a price up to double the current RRP which I suspect few of the target market would pay. LEGO therefore got the size of the hanger right IMHO.
The remainder of the build is the control tower and terminal building. First there is a metal detector screener leading to the waiting/secure area of the airport, which seems taller than it needs to be for the minifigures. I think the same effect could have been made with half the height, except that would not allow for an impressive height for the overall tower. However it does seem to be similar to many modern airports with the high ceilings. This area also seems to be someplace to check luggage as evidenced by the rather nifty conveyor belt that comes in a full part. The moving parts of the set include a revolving door (a very tall one, for the first floor) that leads from the secure area of the airport out to the tarmac, and of course the conveyor belt.
The remainder of the build is the control tower and terminal building. First there is a metal detector screener leading to the waiting/secure area of the airport, which seems taller than it needs to be for the minifigures. I think the same effect could have been made with half the height, except that would not allow for an impressive height for the overall tower. However it does seem to be similar to many modern airports with the high ceilings. This area also seems to be someplace to check luggage as evidenced by the rather nifty conveyor belt that comes in a full part. The moving parts of the set include a revolving door (a very tall one, for the first floor) that leads from the secure area of the airport out to the tarmac, and of course the conveyor belt. 
×