The set has an impressive assortment of minifigures - I quite like that it has six, allowing for a lot of play opportunities. All the major parts of the plane - the wing, cockpit, tail and body - are new to this set in their colours. The inside of the plane has a minimal amount of details, with five seats, a galley and a lavatory. The outside of the plane looks quite smart with all the stickers applied.
The main wings are made up of a pair of white 10 x 10 wedge plates with cut corner and no studs in the centre; these are rare, having only previously appeared in two sets in this colour. The red 1 x 1 plate with tooth on each wing tip is also uncommon, having appeared in less than ten sets to date. The sides of the cockpit are made up of stickered red 1 x 4 x 1 panels, and it definitely helps if you concentrate when you apply the stickers, which I clearly didn’t as you can see in the picture below…. The area behind the cockpit canopy is nicely contoured by a red 4 x 4 triple wedge which, I was surprised to discover, has only previously appeared in a single set in this colour. Not to be outdone, however, the large 12 x 2 x 5 tail is appearing for the very first time in red. The hinged trans-black cockpit canopy is yet another rare element, appearing here for only the second time ever; rare it might be, but its pronounced curvature unfortunately means that it somewhat spoils the hitherto sleek lines of the jet. The flipside of this, however, is that the cockpit can comfortably accommodate the pilot.
Bag 4 finishes the fuselage and all that is left are the engines and tail section. You'll notice that this aircraft has a bathroom on board as well as some storage for a non-existent flight attendant. I think this is the first time that LEGO has put some additional details into aircraft besides just seats. Also there is only one pilot for a 2 seat cockpit in the set.
The Lego Group's motto is det bedste er ikke for godt which means roughly "only the best is the best" (more literally "the best is never too good"). This motto, which is still used today, was created by Christiansen to encourage his employees never to skimp on quality, a value he believed in strongly. By 1951 plastic toys accounted for half of the Lego company's output, even though the Danish trade magazine Legetøjs-Tidende ("Toy-Times"), visiting the Lego factory in Billund in the early 1950s, felt that plastic would never be able to replace traditional wooden toys. Although a common sentiment, Lego toys seem to have become a significant exception to the dislike of plastic in children's toys, due in part to the high standards set by Ole Kirk.
Since 1963, Lego pieces have been manufactured from a strong, resilient plastic known as acrylonitrile butadiene styrene (ABS). As of September 2008, Lego engineers use the NX CAD/CAM/CAE PLM software suite to model the elements. The software allows the parts to be optimised by way of mould flow and stress analysis. Prototype moulds are sometimes built before the design is committed to mass production. The ABS plastic is heated to 232 °C (450 °F) until it reaches a dough-like consistency. It is then injected into the moulds at pressures between 25 and 150 tonnes, and takes approximately 15 seconds to cool. The moulds are permitted a tolerance of up to twenty micrometres, to ensure the bricks remain connected. Human inspectors check the output of the moulds, to eliminate significant variations in colour or thickness. According to the Lego Group, about eighteen bricks out of every million fail to meet the standard required. Lego factories recycle all but about 1 percent of their plastic waste from the manufacturing process. If the plastic cannot be re-used in Lego bricks, it is processed and sold on to industries that can make use of it. Lego has a self-imposed 2030 deadline to find a more eco-friendly alternative to the ABS plastic it currently uses in its bricks.
I purchased this set the day it was released for my LEGO City, as an upgrade from my previous airport (10159 Airport from 2004). First off, the build is great and although it's not very challenging, it's exciting to see the plane come to life and the use of the big plane pieces (eg. the nose, the wings, the tail etc.) was new to me, though I know there have been a number of planes in the past that use these pieces. There are 4 instruction booklets (2 for the plane, one for the airport, and one for the luggage/fuel/stairs car), 8 numbered bags, and two separate bags with the bigger pieces in. This makes the build very easy to follow. The completed set is very grand (especially the plane) in scale, and great looking. It's nice to see that a different colour scheme been used for the plane as opposed to the usual red and white or blue and white colours as seen in previous sets. The plane is HUGE, with a wingspan of around 2 32-wide baseplates (bare this in mind if you want to make a runway). However, despite its huge size, the inside of the plane is very bare. There are 5 seats for the passengers, another one facing backwards which I presume is for the cabin crew (although there isn't a cabin crew minifigure, which would have been a nice addition), and two seats in the cockpit. There's a tiny bathroom at the back of the plane, and a small galley area at the front with a sink and cupboard. There's easily room for a sixth chair in the plane, which I think should have been included, and the space within the plane could've been arranged better to fully optimise the area. The airport terminal has a very nice modern look, and includes the revolving door, tower, waiting area, security scanner and check in desk with luggage conveyor. Although this sounds like a lot of features, the inside of the terminal is, again, very bare and the space could've been used better. There are only 4 seats in the waiting area, and a lot of the space is taken up by the revolving door. The operational conveyor belt for the luggage is a nice touch, though, and there is a fair bit of playability within. The service car is a nice addition to this set and gives it more playability. All the trailers (fuel, stairs and luggage) connect together and attach to the service car, which has a really cool "follow me" sign on the back. This is a really nice addition to the set. Overall, I really like this set because of how it looks and because there's plenty of opportunity for play, but I think a lot more thought could've gone into maximising the space within the plane and the airport. Some more minifigures would have been good, such as a member of the cabin crew, a check-in clerk and a security officer. The value for money is okay with this set, as you do get a lot of big pieces, but the bare interiors are a little disappointing for the price you pay.
This detailed model features a classic red, black and grey colour scheme, large driver's cab with detailed dashboard, wing mirrors, opening tool storage compartment, 4-cylinder engine with moving pistons, twin-axle steering, double rear axle and chunky tires. Activate the boom to position the water cannon and extinguish the flames! This Power Functions upgradable model can be rebuilt to create an awesome Fire Rescue Vehicle!
From mid-2009, the airport was served by 9 airlines flying regular flight service, of which KLM had the busiest route with over 200,000 annual passengers to Amsterdam Schiphol. In 2011, Ryanair announced that Billund Airport with effect from 25 March 2012 would be the base for two Boeing 737 aircraft. At the same time Ryanair published 5 new routes, so that, from the summer of 2012, they would fly to 19 destinations.
Here’s a look at the Winter Soldier and Captain America minifigures. Unfortunately, neither one of them is exclusive to this set, with this version of Winter Soldier making an appearance in 76047 Black Panther Pursuit. Captain America has been a lot more promiscuous, having made an appearance in 2 sets (Quinjet City Chase & Hydra Fortress Smash) and a polybag as well. His torso is also identical to the one from Black Panther Pursuit.