The body of the plane is built with five seats for passengers. The wings are added next with what I think are filler stickers added to the top of the wings. There is a small galley with sink and oven in the front of the plane right behind the cockpit. The cockpit uses only one sticker to show navigation equipment - the other is printed, which is always welcome (though not a new piece). A lavatory is installed in the back, and then the inside is complete. There is an odd choice for the door to the lav - a swinging door. Not much opportunity for privacy!
^ Jump up to: a b Alexander, Ruth (3 December 2012). "How tall can a Lego tower get?". BBC News. Archived from the original on 4 December 2012. Retrieved 4 December 2012. The average maximum force the bricks can stand is 4,240N. That's equivalent to a mass of 432 kg (950lbs). If you divide that by the mass of a single brick, which is 1.152g, then you get the grand total of bricks a single piece of Lego could support: 375,000. So, 375,000 bricks towering 3.5 kilometers (2.17 miles) high is what it would take to break a Lego brick.
Will agree with some other reviewers that some parts will fall off with normal-rough play. However, the attention to detail is pretty cool and almost makes up for it. The top is hard to take off and put on to move the minifigs. There is a TSA checkpoint, a conveyor belt for luggage, a rather impressive runway vehicle. Couple this with the cargo plane or another airplane set and some atraight road nameplates, you got an airport without spending a fortune.
Stickers are used for decorations for the outside of the plane. I like how the stickers for the outside match colours with the piping on the plane. I found the sticker for the top of the door to be a little big; if you line up the orange on the bottom of the stickers with the orange on the plane the sticker overlaps a bit at the top. The stickers for the nose of the plane are not as difficult to apply as I thought they would be. They do seem a bit superfluous, though they do make the plane look nice. The plane is finished with the tail fin, that uses yet more stickers. It is interesting that this plane actually uses more stickers than the Friends plane does.
Will agree with some other reviewers that some parts will fall off with normal-rough play. However, the attention to detail is pretty cool and almost makes up for it. The top is hard to take off and put on to move the minifigs. There is a TSA checkpoint, a conveyor belt for luggage, a rather impressive runway vehicle. Couple this with the cargo plane or another airplane set and some atraight road nameplates, you got an airport without spending a fortune.
Apart from that, both carriers have extensive networks within Europe and the Mediterranean (including North Africa and the Middle East). SAS flies to most European capitals, and has a particularly dense network of connections across the Baltic Sea, to Finland, Estonia, Latvia and Lithuania, as well as to Poland, where it serves the majority of even small airports. There is also a fairly good network of connections to the United Kingdom and, perhaps surprisingly, to Italy, where even smaller airports like Bologna are served.

Primary concept and development work takes place at the Billund headquarters, where the company employs approximately 120 designers. The company also has smaller design offices in the UK, Spain, Germany, and Japan which are tasked with developing products aimed specifically at these markets. The average development period for a new product is around twelve months, split into three stages. The first stage is to identify market trends and developments, including contact by the designers directly with the market; some are stationed in toy shops close to holidays, while others interview children. The second stage is the design and development of the product based upon the results of the first stage. As of September 2008 the design teams use 3D modelling software to generate CAD drawings from initial design sketches. The designs are then prototyped using an in-house stereolithography machine. These prototypes are presented to the entire project team for comment and for testing by parents and children during the "validation" process. Designs may then be altered in accordance with the results from the focus groups. Virtual models of completed Lego products are built concurrently with the writing of the user instructions. Completed CAD models are also used in the wider organisation, for marketing and packaging.[33]
Agent 13 has a pretty plain appearance, with caramel-coloured wavy hair, and a black, spy-like top. Her torso has some nice details, with sharp, angular lines that all combine to form a rough outline of an upside down star. She has plain sand blue pants and rocks a sub-machine gun accessory. I like regular LEGO firearms, so it’s very nice to get one in this set as they’re fairly uncommon.
×