It’s always tough to sum up a set that has the sort of price tag that this one carries; because it doesn’t necessarily offer the collectors value that a Marvel or Star Wars set will offer, it can be a little harder to justify an outlay on, in this case, a few planes and a aircraft hangar. However, if you have a love for the City range, whether it be a nostalgic look back at your childhood, the general consistently-superior design of the range, or simply because your kids want an airport to build, this one has to be recommended. Once I finished building this, I set it up in my daughter’s bedroom, and the overjoyed expression on her face, followed by the extended time taken to play with the planes and flying them all over her room, made every single minute of the build worthwhile. Watching her swirl around her room – and later, the rest of house – clutching the planes and bringing them in for landings into the hangar, reminded me of why I fell in love with LEGO in the the first place; imagination.
In December 2012, the BBC's More or Less radio program asked the Open University's engineering department to determine "how many Lego bricks, stacked one on top of the other, it would take for the weight to destroy the bottom brick?" Using a hydraulic testing machine, the engineering department determined the average maximum force a 2×2 Lego brick can stand is 4,240 newtons; since an average 2×2 Lego brick has a mass of 1.152 grams (0.0406 oz), according to their calculations it would take a stack of 375,000 bricks to cause the bottom brick to collapse, which represents a stack 3,591 metres (11,781 ft) in height.
Will agree with some other reviewers that some parts will fall off with normal-rough play. However, the attention to detail is pretty cool and almost makes up for it. The top is hard to take off and put on to move the minifigs. There is a TSA checkpoint, a conveyor belt for luggage, a rather impressive runway vehicle. Couple this with the cargo plane or another airplane set and some atraight road nameplates, you got an airport without spending a fortune.
The remainder of the build is the control tower and terminal building. First there is a metal detector screener leading to the waiting/secure area of the airport, which seems taller than it needs to be for the minifigures. I think the same effect could have been made with half the height, except that would not allow for an impressive height for the overall tower. However it does seem to be similar to many modern airports with the high ceilings. This area also seems to be someplace to check luggage as evidenced by the rather nifty conveyor belt that comes in a full part. The moving parts of the set include a revolving door (a very tall one, for the first floor) that leads from the secure area of the airport out to the tarmac, and of course the conveyor belt.
The final two minifigures are the Biplane Pilot and the intrepid Wing Walker. Both of these minifigures share the same white torso which is printed with a flight suit design overlaid with dark red and bright light orange flames plus a logo over the left breast. The torso design is superb and it can at present only be found in this set. Both minifigures are provided with a reddish brown aviator cap and dark bluish grey goggles, and the pilot (below left) also gets an alternative to this headgear in the form of medium dark flesh mid-length hair which has only ever appeared in five sets in this colour.
It’s been three years since the release of the most recent City Airport set, namely, 60019 Stunt Plane, and a full six years since LEGO gave us a number of Airport releases at any one time. Of the five summer 2016 Airport releases, 60103 Airport Air Show was one of those that I was most interested to get my hands on, and I’m pleased to be able to bring you a review of it today.
The last of the three aircraft is a modern biplane. This incorporates a number of rare orange elements including right and left 8 x 3 wedge plates which make up the wings and have only previously appeared in three sets, a 3 x 4 wedge brick only previously found in two sets, and a 3 x 6 round half plate with a 1 x 2 cutout which has only previous appeared in a single set in this colour and which forms the tailplanes. Similar to the two jets the tail fin is stickered rather than printed, as are the pair of 1 x 4 x 1 panels making up the sides of the cockpit. Unlike the jets, however, the instrument panel is stickered, which seems odd as there are existing printed 1 x 2 light bluish grey tiles which could have done an acceptable job. There are also a pair of stickers which represent the engine exhausts and which are applied to a couple of modified 2 x 4 x 1 1/3 bricks with curved top which sit just behind the propeller; applying these neatly to the curved surface takes a steady hand, and that’s also the case for the pair of checkerboard stickers which are stuck onto the propeller cowl. As if stickered exhausts weren’t enough, there are also a couple of light bluish grey exhaust pipes with Technic pin which emerge from the propeller cowl and run along either side of the fuselage. They’re entirely superfluous given the presence of the stickered exhausts but they still look cool regardless!
I'm not sure what to make of the set yet. I like the planes (although that biplane really doesn't need the bubble canopy). The idea of adding a hangar is interesting and I don't mind that it's a bit open. But the fact that it'll only house one of the three planes is annoying. Having said that, I'm not sure what you could do about it. Tripling the hangar would make it big and boring and push the price up. Could they have done two planes and a double hangar?
Parking capacity at Copenhagen Airport was greatly expanded in 2015 with the construction of a new lot as one of the first phases in an ambitious airport expansion plan scheduled to roll out in the coming decades. There are several lots: those near the terminals are very expensive, while the further-flung ones are cheaper (but have free shuttle bus service to the terminals).
We are a collective bunch of geeks who love to share our passion with the rest of the world. Just like the Beholder we have adopted as our mascot, we have both depth and width of geeky topics we cover. By visiting this page, you declare yourself one of us! If you have grown up with a steady diet of all things related to video games, Star Wars, Star Trek, sci-fi, gadgets, toys, Transformers one way or another, this will be your second home.
The main wings are made up of a pair of white 10 x 10 wedge plates with cut corner and no studs in the centre; these are rare, having only previously appeared in two sets in this colour. The red 1 x 1 plate with tooth on each wing tip is also uncommon, having appeared in less than ten sets to date. The sides of the cockpit are made up of stickered red 1 x 4 x 1 panels, and it definitely helps if you concentrate when you apply the stickers, which I clearly didn’t as you can see in the picture below…. The area behind the cockpit canopy is nicely contoured by a red 4 x 4 triple wedge which, I was surprised to discover, has only previously appeared in a single set in this colour. Not to be outdone, however, the large 12 x 2 x 5 tail is appearing for the very first time in red. The hinged trans-black cockpit canopy is yet another rare element, appearing here for only the second time ever; rare it might be, but its pronounced curvature unfortunately means that it somewhat spoils the hitherto sleek lines of the jet. The flipside of this, however, is that the cockpit can comfortably accommodate the pilot.
Agent 13 has a pretty plain appearance, with caramel-coloured wavy hair, and a black, spy-like top. Her torso has some nice details, with sharp, angular lines that all combine to form a rough outline of an upside down star. She has plain sand blue pants and rocks a sub-machine gun accessory. I like regular LEGO firearms, so it’s very nice to get one in this set as they’re fairly uncommon.