Airport Passenger Terminal with control tower and conveyor belt measures over 11” high, 12” wide and 4” deep. Airplane measures over 7” high, 18” long and 19” wide. Service car measures over 1” high, 2” long and 1” wide. Luggage trailer measures over 3" long, 1" high and 1" wide. Fuel trailer measures over 1” high, 3” long and 1” wide. Mobile stairway measures over 2” high, 2” long and 1” wide
Parking capacity at Copenhagen Airport was greatly expanded in 2015 with the construction of a new lot as one of the first phases in an ambitious airport expansion plan scheduled to roll out in the coming decades. There are several lots: those near the terminals are very expensive, while the further-flung ones are cheaper (but have free shuttle bus service to the terminals).
The last of the three aircraft is a modern biplane. This incorporates a number of rare orange elements including right and left 8 x 3 wedge plates which make up the wings and have only previously appeared in three sets, a 3 x 4 wedge brick only previously found in two sets, and a 3 x 6 round half plate with a 1 x 2 cutout which has only previous appeared in a single set in this colour and which forms the tailplanes. Similar to the two jets the tail fin is stickered rather than printed, as are the pair of 1 x 4 x 1 panels making up the sides of the cockpit. Unlike the jets, however, the instrument panel is stickered, which seems odd as there are existing printed 1 x 2 light bluish grey tiles which could have done an acceptable job. There are also a pair of stickers which represent the engine exhausts and which are applied to a couple of modified 2 x 4 x 1 1/3 bricks with curved top which sit just behind the propeller; applying these neatly to the curved surface takes a steady hand, and that’s also the case for the pair of checkerboard stickers which are stuck onto the propeller cowl. As if stickered exhausts weren’t enough, there are also a couple of light bluish grey exhaust pipes with Technic pin which emerge from the propeller cowl and run along either side of the fuselage. They’re entirely superfluous given the presence of the stickered exhausts but they still look cool regardless!
Manufacturing of Lego bricks occurs at several locations around the world. Moulding is done in Billund, Denmark; Nyíregyháza, Hungary; Monterrey, Mexico and most recently in Jiaxing, China. Brick decorations and packaging are done at plants in Denmark, Hungary, Mexico and Kladno in the Czech Republic. The Lego Group estimates that in five decades it has produced 400 billion Lego blocks. Annual production of Lego bricks averages approximately 36 billion, or about 1140 elements per second. According to an article in BusinessWeek in 2006, Lego could be considered the world's No. 1 tire manufacturer; the factory produces about 306 million small rubber tires a year. The claim was reiterated in 2012.
While I like their characters, I really don’t like LEGO recycling their characters. I can make an exception for Bucky, who until this year has only been made available as a pretty exclusive (and pricey) polybag but having this exact same Captain America show up in so many sets is pretty damn lazy. If a super hero minifig has been used a year ago, it really isn’t too much to ask for LEGO to update it slightly.
Since 1963, Lego pieces have been manufactured from a strong, resilient plastic known as acrylonitrile butadiene styrene (ABS). As of September 2008, Lego engineers use the NX CAD/CAM/CAE PLM software suite to model the elements. The software allows the parts to be optimised by way of mould flow and stress analysis. Prototype moulds are sometimes built before the design is committed to mass production. The ABS plastic is heated to 232 °C (450 °F) until it reaches a dough-like consistency. It is then injected into the moulds at pressures between 25 and 150 tonnes, and takes approximately 15 seconds to cool. The moulds are permitted a tolerance of up to twenty micrometres, to ensure the bricks remain connected. Human inspectors check the output of the moulds, to eliminate significant variations in colour or thickness. According to the Lego Group, about eighteen bricks out of every million fail to meet the standard required. Lego factories recycle all but about 1 percent of their plastic waste from the manufacturing process. If the plastic cannot be re-used in Lego bricks, it is processed and sold on to industries that can make use of it. Lego has a self-imposed 2030 deadline to find a more eco-friendly alternative to the ABS plastic it currently uses in its bricks.
The body of the plane is built with five seats for passengers. The wings are added next with what I think are filler stickers added to the top of the wings. There is a small galley with sink and oven in the front of the plane right behind the cockpit. The cockpit uses only one sticker to show navigation equipment - the other is printed, which is always welcome (though not a new piece). A lavatory is installed in the back, and then the inside is complete. There is an odd choice for the door to the lav - a swinging door. Not much opportunity for privacy!
The final two minifigures are the Biplane Pilot and the intrepid Wing Walker. Both of these minifigures share the same white torso which is printed with a flight suit design overlaid with dark red and bright light orange flames plus a logo over the left breast. The torso design is superb and it can at present only be found in this set. Both minifigures are provided with a reddish brown aviator cap and dark bluish grey goggles, and the pilot (below left) also gets an alternative to this headgear in the form of medium dark flesh mid-length hair which has only ever appeared in five sets in this colour.