The Lego Group's motto is det bedste er ikke for godt which means roughly "only the best is the best" (more literally "the best is never too good"). This motto, which is still used today, was created by Christiansen to encourage his employees never to skimp on quality, a value he believed in strongly. By 1951 plastic toys accounted for half of the Lego company's output, even though the Danish trade magazine Legetøjs-Tidende ("Toy-Times"), visiting the Lego factory in Billund in the early 1950s, felt that plastic would never be able to replace traditional wooden toys. Although a common sentiment, Lego toys seem to have become a significant exception to the dislike of plastic in children's toys, due in part to the high standards set by Ole Kirk.
There are 3 cardboard boxes with more Easter eggs. We get a few references to Marvel organisations such as A.I.M., who you may remember from Iron Man 3 as an R&D agency run by Aldrich Killian, Hammer, one of Stark Industries primary rivals which made an appearance in Iron Man 2, bankrolling Whiplash and finally a box with the Stark Industries logo on it.
In December 2012, the BBC's More or Less radio program asked the Open University's engineering department to determine "how many Lego bricks, stacked one on top of the other, it would take for the weight to destroy the bottom brick?" Using a hydraulic testing machine, the engineering department determined the average maximum force a 2×2 Lego brick can stand is 4,240 newtons; since an average 2×2 Lego brick has a mass of 1.152 grams (0.0406 oz), according to their calculations it would take a stack of 375,000 bricks to cause the bottom brick to collapse, which represents a stack 3,591 metres (11,781 ft) in height.
If you don’t own Black Panther Pursuit or any of the sets that included Captain America, I guess it would a plus getting the both of them in this set but Super Heroes collectors tend to be completionists, so I think that scenario will be particularly rare. I guess you could always sell your spares on the secondary market, but really, who wants to do that?
Thanks for the great review and comparison. I've thought about getting the Friends Airport for my daughter, as we both like the amount of detail inside the plane. Why would Lego think that boys don't care as much about detail? I love the wider body planes, but it's a shame they're not producing the runway plates, or including them in the airport sets, anymore. I agree with ZeeBricks that if they're not going to include everything an airport needs (although as expensive as price/piece these sets are getting it would cost a fortune) they should sell smaller sets that can be added together. Now that I'm feeling nostalgic for classic airport I might rebuild my 6392 and dust off my 6396 and set them up tonight, it's time for some serious swooshing :)
Since 1963, Lego pieces have been manufactured from a strong, resilient plastic known as acrylonitrile butadiene styrene (ABS). As of September 2008, Lego engineers use the NX CAD/CAM/CAE PLM software suite to model the elements. The software allows the parts to be optimised by way of mould flow and stress analysis. Prototype moulds are sometimes built before the design is committed to mass production. The ABS plastic is heated to 232 °C (450 °F) until it reaches a dough-like consistency. It is then injected into the moulds at pressures between 25 and 150 tonnes, and takes approximately 15 seconds to cool. The moulds are permitted a tolerance of up to twenty micrometres, to ensure the bricks remain connected. Human inspectors check the output of the moulds, to eliminate significant variations in colour or thickness. According to the Lego Group, about eighteen bricks out of every million fail to meet the standard required. Lego factories recycle all but about 1 percent of their plastic waste from the manufacturing process. If the plastic cannot be re-used in Lego bricks, it is processed and sold on to industries that can make use of it. Lego has a self-imposed 2030 deadline to find a more eco-friendly alternative to the ABS plastic it currently uses in its bricks.
Colour-wise, it is mainly yellow, with only a dash of green and red, and a little more white, there to break it up. The worker has space to stand and drive the vehicle, and has a walkie talkie attached on the side of the car. Around the other side is a coiled-up, what I assume is a, fuel pump. It looks pretty good when coiled up on the side of the car. Stickers come into use again here, this time for the number plates.
As is the norm with LEGO sets these days, there are a fair few stickers in use for this item. I’m still not a fan of their use, but at this point in time, it is something I have come to expect and just get on with it now. In their defence, they do add to the overall presentation, making it that little bit harder to complain. As I said, this is my favourite of the three planes in the set, mainly because it looks superb and offers a great build experience. Seriously, I had so much fun building this. The instructions – as always – are clear, and it is not going to provide any major issues. Stability-wise, there are no concerns here, with the finished product very sturdy and, as proved by my daughter, can handle itself when being flown around the room by an excited seven-year-old. One minifigure can be seated at the controls, with suitable space for application and removal. The other pilot has its place on the top of the plane, with a single piece of black fencing to provide support for the death-defying pilot.
Compared to other major European hub airports, like Charles de Gaulle or Heathrow, CPH has a similar number of connections, but is much smaller in both actual size and passenger volumes, and can provide a calmer, more pleasant experience. Its location in the south of Scandinavia makes reaching most European destinations reasonable, and flying to destinations in the Baltic region and in Eastern Europe generally only takes half the time as from major hub airports in Western Europe.